9700A CAT6 AT&T Network Ready 4G LTE Router

Search Cable Adapters

Find other Device Pigtails

Because the 9700A CAT6 AT&T Network Ready 4G LTE Router device has an external antenna port you could use the high gain external antenna kits above to boost your signal. However, if your outdoor signal is very weak, or you require a very long cable run to get from the outdoor antenna to the device (long runs lead to large signal loss) consider using an RF bidirectional amplifier/ repeater suitable for the supported bands and cellular operator to boost your indoor coverage:

LTE Antenna Boosters/ RF Bidirectional Amplifiers/ Repeaters/ Relays

STEP 1: Determine what frequency bands your operator uses here, then click on the frequency band link to view the best ranked cellular antennas compatible with the frequency band that both your device and your cellular operator supports. Your 9700A CAT6 AT&T Network Ready 4G LTE Router operates on these frequency bands: LTE Band 1, LTE Band 2, LTE Band 3, LTE Band 4, LTE Band 5, LTE Band 7, LTE Band 8, LTE Band 12, LTE Band 13, LTE Band 20, LTE Band 25, LTE Band 26, LTE Band 29, LTE Band 30, LTE Band 41.

STEP 2: Determine the cable length you need from the outdoor antenna to the 9700A CAT6 AT&T Network Ready 4G LTE Router and configure your length here (select N-Male on both ends)

STEP 3: Determine if you need a lightning protection device. If you do, you will need a jumper cable.

STEP 4: Order the pigtail for your modem below:

STEP 5: If the pigtail's Connector 2 is FME-F you will need an N-Female/FME-F adapter to mate to the N-Male cable in step 2. Alternatively, select an N-Male/FME-M cable in step 2 above (more expensive and less re-usable) to avoid requiring this adapter.

Contact us if unsure about any of the steps above or for help configuring your coverage/speed improvement solution or visit our support website to learn more.

See below for other LTE antennas or contact us if you cannot find what you are looking for

Other LTE Antennas

Best 2.4/5 GHz Wi-Fi Replacement Antennas (Rubber Duck)

Best 2.4/5 GHz Wi-Fi Ceiling Dome Antennas

Best 2.4/5 GHz Wi-Fi Panel Antennas

Best 2.4/5 GHz Wi-Fi Omni Antennas

Vehicle Wi-Fi Antennas

Other WLAN Antennas

Please contact us for updates on what pigtail/adapter you need to attach an external antenna to this device as the antenna port type is currently not listed in RFWEL's Wireless Device Database.

Search Other Adapters/ Connectors

Because the 9700A CAT6 AT&T Network Ready 4G LTE Router device has an external antenna port, you could use the high gain external antenna kits above to boost your signal. However, if your access point is very far, or you need to reach a WLAN station that is very far, or you require a very long cable run to get from the antenna mounting location to the device (long runs lead to large signal loss) consider using other Wi-Fi signal extension solutions as indicated below.

Wi-Fi Coverage Extension Solutions

See below for wireless site components to integrate 9700A CAT6 AT&T Network Ready 4G LTE Router to your wireless infrastructure

Outdoor Radio Enclosure

Low loss RF Cables

Other Wireless Site Accessories

See below for remote and backup power solutions for 9700A CAT6 AT&T Network Ready 4G LTE Router

Off-Grid Solar Solutions

Remote Power Solutions

Indoor coverage solutions

Select Case Studies

Support Knowledge Base

Search 9700A articles

Discuss in the Forums

Search 9700A posts

Ask a Question

Select Engineering Drawings

Mobile communication trailer

Residential Solution for Multi-WAN connectivity and Wi-Fi

View More Engineering Drawings ...