|
|
|
U-LTE-US Ubiquiti Networks UniFi LTE US
The UniFi LTE can be placed anywhere since it can be powered by 802.3at PoE+ from a UniFi PoE switch. Should you require greater LTE coverage and performance, you can attach an optional high-gain antenna to the RP?SMA antenna connector for a stronger signal.
| Buy U-LTE-US from these Online Market Places |
|
|
| Signal Improvement Solutions (Cellular) |
| U-LTE-US Ubiquiti Networks UniFi LTE US includes an antenna port to attach external cellular antennas. See below for different options for high gain and high performance indoor and outdoor antennas to improve the signal strength and indoor coverage. Additionally, see below for RF bidirectional amplifiers/ distributed antenna systems/ repeaters/ small cells to further improve indoor coverage without directly attaching pigtail/ cable the device. |
| Pigtail for External Cellular Antenna |
| Cellular Repeaters/ Bi-Directional Amplifiers |
|
Because the U-LTE-US Ubiquiti Networks UniFi LTE US device has an external antenna port you could use the high gain external antenna kits above to boost your signal. However, if your outdoor signal is very weak, or you require a very long cable run to get from the outdoor antenna to the device (long runs lead to large signal loss) consider using an RF bidirectional amplifier/ repeater suitable for the supported bands and cellular operator to boost your indoor coverage: LTE Antenna Boosters/ RF Bidirectional Amplifiers/ Repeaters/ Relays |
| Customize your solution |
|
STEP 1: Determine what frequency bands your operator uses here, then click on the frequency band link to view the best ranked cellular antennas compatible with the frequency band that both your device and your cellular operator supports. Your U-LTE-US Ubiquiti Networks UniFi LTE US operates on these frequency bands: LTE Band 2, LTE Band 4, LTE Band 5, LTE Band 12.
STEP 2: Determine the cable length you need from the outdoor antenna to the U-LTE-US Ubiquiti Networks UniFi LTE US and configure your length here (select N-Male on both ends)
STEP 3: Determine if you need a lightning protection device. If you do, you will need a jumper cable.
STEP 4: Order the pigtail for your modem below:
STEP 5: If the pigtail's Connector 2 is FME-F you will need an N-Female/FME-F adapter to mate to the N-Male cable in step 2. Alternatively, select an N-Male/FME-M cable in step 2 above (more expensive and less re-usable) to avoid requiring this adapter.
Contact us if unsure about any of the steps above or for help configuring your coverage/speed improvement solution or visit our support website to learn more. See below for other LTE antennas or contact us if you cannot find what you are looking for |
| Wireless Site & Infrastructure Solutions |
|
See below for wireless site components to integrate U-LTE-US Ubiquiti Networks UniFi LTE US to your wireless infrastructure |
| Power Solutions |
|
See below for remote and backup power solutions for U-LTE-US Ubiquiti Networks UniFi LTE US |
| Additional Device Support |
|
Select Engineering Drawings |
-
Cellular OperatorsATT
-
Brand/ ManufUbiquiti
-
Device TypeLTE Gateway
- Cellular Specifications
-
Cellular BandsLTE Band 12, LTE Band 5, LTE Band 4, LTE Band 2
-
Cell Antenna Port?Yes
-
Cell Antenna Port TypeRPSMA-Female
-
# of Cell Antenna Ports1
-
LTE CategoryCategory 4
-
- Electrical
-
Voltage Input Range44 to 57 V
-
Power (Watts)8.5
-
PoE?Yes
-
POE TypeType 2 POE+ (802.3at)
-
- Mechanical
-
Weight (lbs)0.7
-
Dimensions (inch)7.96 x 1.26 x 2.6
-